logo
Home » Products » gas cutting pressure

Information on Cutting Gases,

As MAPP gas can be used at a higher pressure than acetylene, it can be used for underwater cutting in deep water as it is less likely to dissociate into its components of carbon and hydrogen which are explosive.

View More >>

Gas Nozzle Pressures (Oxy/Acet+Oxy/Propane)- The Welders ...

state under a pressure of 29.4 pounds per square inch (psi). A slight shock is likely to cause it to explode. WARNING Acetylene becomes extremely dangerous if used above 15 pounds pressure.

View More >>

Fiber laser cutting assist gas technology evolves

Bharat Petroleum Corporation Limited. While not only dealing with natural gas, Bharat Petroleum also works with oil for a variety of needs. Bharatgas, one of BPCL’s seven business units, is engaged in marketing LPG and propane for industries, hotels, malls, IT parks, automobiles, etc. Bharatgas also offers industrial services, including customer advisory services, energy audits, e-banking ...

View More >>

What do you need to know about gas cutting?

During the laser cutting process, a laser is used as a heat source to melt or vaporize materials. To cut the materials with a high-quality edge, an assist gas blows through a cutting nozzle on the laser cutting head. Then the molten material pushes out of the hot spot where the laser light is hitting the material. This area is known as the kerf.

View More >>

Oxy-Propane-Cutting-What Settings?

High Pressure Technologies offers over 30 years of engineering experience in providing turn-key plug & play solutions for high pressure applications for gas, liquid, and air. We are a leading supplier of high pressure equipment and specialize in distributing the maximator® range of air driven liquid pumps, air amplifiers, and gas boosters.

View More >>

Guidelines for Gas Welding and Cutting - BOC

pressure as tip size increases. VICTOR Propane, LPG & Natural Gas Cutting Tip Chart Cutting Tip Series MTHN (High Speed Machine Cutting) Metal Thickness Tip Size Cutting Oxygen (PSIG)* Preheat Oxygen (PSIG) Preheat Fuel Gas (PSIG) Speed I.P.M. Kerf Width 1/4" 00 85/95 23/30 .05 3/8" 00 85/95 23/30 .05 1/2" 0 85/95 18/26 .06 3/4" 0 85/95 17/24 .06 1" 1 85/95 15/22 .07

View More >>

Oxy Acetylene Cutting Torch Pressure Settings For Cutting

MAPP gas can be used at much higher pressures than acetylene, sometimes up to 40 or 50 psi in high-volume oxy-fuel cutting torches which can cut up to 12-inch-thick (300 mm) steel. Other welding gases that develop comparable temperatures need special procedures for safe shipping and handling.

View More >>

Pressure regulator - Wikipedia

Jun 25, 2021 · Effect on cutting quality: Firstly.The cutting gas helps to dissipate heat and assist combustion, and blows off the melt to obtain a better quality cut section. Secondly.When the pressure of the cutting gas is insufficient,the melting will occur during cutting. And the cutting speed cannot meet the production efficiency.

View More >>

High Pressure Notification Request Form | ATCO

There is a variety of gas cutting nozzle types in the market. Each is chosen depending on the size, torch type, material, bore diameter, thickness to be cut, and the pressure of oxygen. These nozzles have extensive use in the fabrication industry, each delivering a certain specific cut.

View More >>

Oxy Acetylene Welding (OFW) Fundamentals Pressure Settings ...

8 rows · Oxy-fuel cutting is a thermal cutting process that uses oxygen and fuel gas (such as ...

View More >>

Flame Cutting - gas-tec.com

4. Screw in the regulator adjusting knobs slowly until the delivery pressure gauges are both correct. 5. Purge the oxygen gas line and check for constant gas flow. Re-adjust delivery pressure if necessary. 6. Then purge the acetylene gas line and check for constant gas flow. Re-adjust pressure if necessary. 7.

View More >>

CONCOA - Gas Pressure Regulators, Cutting and Welding ...

Gas cutting nozzles are supplied in various types. There are three main globally recognized and frequently used nozzles. They are supplied in different sizes, material, bore diameters, and pressure tolerance ability. This attracts a different gas cutting nozzle price on each piece.

View More >>

Laser Cutting Assist Gas Pressure Control | by Proportion-Air

The maximum working pressure for acetylene gas when using a cutting torch is 15 psi or 103.4 kPa. If the pressure goes beyond that, raw acetylene gets unstable and becomes dangerous to use. Acetylene is a flammable gas and when it becomes unstable, it is at risk of spontaneously combusting.

View More >>

Guidelines for Gas Welding and Cutting - BOC

Gas Pressure - Cutting Oxygen: 35-40 psig: Gas Pressure - Fuel Gas: 4-8 psig: Part Number: 0333-0401: Total Fuel Gas Consumption: 12-15 cfh: Total Oxygen Consumption: 115-125 cfh: Total Preheat Oxygen Consumption : 23-108 cfh

View More >>

Laser cutting, no gas delivery trucks required

Where a liquid oxygen system is to be used to supply gaseous oxygen for welding or cutting and the system has a storage capacity of more than 13,000 cubic feet (364 m 3) of oxygen (measured at 14.7 psia (101 kPa) and 70 °F (21.1 °C)), ... High-pressure fuel-gas manifolds shall be provided with approved pressure regulating devices. 1910.253(c)(2)

View More >>

Cutting, Welding/Brazing and Heating Tip Flow and Pressure Data

† Listed pressure for 3-hose machine cutting torches only. Regulator pressures are for 50 ft (13 m) or less of 3/8 in. (10mm) I.D. hose. Increase regulator pressures if longer hose or smaller I.D. hose is used. If more than 100 ft (31 m) of hose is required, use 1/2 in. (13 mm) I.D. hose for additional length.

View More >>

© Copyright: Shanghai Huawei Welding & Cutting Machine Co., Ltd.. All rights reserved.
top